dlp DD-WRT Novice
Joined: 04 Jan 2024 Posts: 2
|
Posted: Fri Jan 05, 2024 0:05 Post subject: USB device not listed in dmesg |
|
DD-WRT v3.0-r52485
Netgear 6350
I've just installed DD-WRT on my router and it all works except the USB, which I'm trying to use a 16gb thumb drive as a NAS. I've read other posts about this, and tried various formats (NTFS, FAT32, EXT4), but no matter what, I see only the USB hub listed in DMESG, no USB devices and no errors other than something about low power mode. Nothing in the /mnt folder or anything that looked like it in the /dev folder. Commands like lsusb and lsblk don't seem to be supported but fdisk shows no other drives than the router. With the stock Netgear firmware the thumb drive works fine.
Does this build not support flash drives?
Thank you.
Code: |
Trying 192.168.1.1...
Connected to 192.168.1.1.
Escape character is '^]'.
DD-WRT v3.0-r52485 std (c) 2023 NewMedia-NET GmbH
Release: 05/11/23
Board: Netgear R6350
DD-WRT login: root
Password:
==========================================================
___ ___ _ _____ ______ ____ ___
/ _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \
/ // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // /
/____/____/ |__/|__/_/|_| /_/ |___/____(_)___/
DD-WRT v3.0
https://www.dd-wrt.com
==========================================================
BusyBox v1.36.0 (2023-05-11 08:35:01 +06) built-in shell (ash)
]0;root@DD-WRT: ~[01;31mroot@DD-WRT[00m:[01;34m~[00m# dmesg
[ 0.000000] Linux version 4.14.313 (root@linux) (gcc version 13.1.0 (OpenWrt GCC 13.1.0 r22658+9-2c530fcb97)) #3785 SMP Thu May 11 08:32:35 +06 2023
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Netgear R6350
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 80708380, node_mem_map 81003000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] percpu: Embedded 14 pages/cpu s26224 r8192 d22928 u57344
[ 0.000000] pcpu-alloc: s26224 r8192 d22928 u57344 alloc=14*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,57600 console=ttyS0,57600n8 rootfstype=squashfs noinitrd
[ 0.000000] log_buf_len individual max cpu contribution: 4096 bytes
[ 0.000000] log_buf_len total cpu_extra contributions: 12288 bytes
[ 0.000000] log_buf_len min size: 16384 bytes
[ 0.000000] log_buf_len: 32768 bytes
[ 0.000000] early log buf free: 14368(87%)
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00072454
[ 0.000000] Readback ErrCtl register=00072454
[ 0.000000] Memory: 121952K/131072K available (5883K kernel code, 269K rwdata, 1040K rodata, 216K init, 224K bss, 9120K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[ 0.015553] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.087880] pid_max: default: 32768 minimum: 301
[ 0.097187] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.110207] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.125827] Hierarchical SRCU implementation.
[ 0.134961] smp: Bringing up secondary CPUs ...
[ 8.611360] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 8.611368] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 8.611379] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 8.611522] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.204625] Synchronize counters for CPU 1: done.
[ 8.734937] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 8.734944] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 8.734952] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 8.735011] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.325097] Synchronize counters for CPU 2: done.
[ 8.852137] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 8.852144] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 8.852152] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 8.852216] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.444655] Synchronize counters for CPU 3: done.
[ 0.504240] smp: Brought up 1 node, 4 CPUs
[ 0.516329] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.535796] futex hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.548229] pinctrl core: initialized pinctrl subsystem
[ 0.559416] NET: Registered protocol family 16
[ 0.576974] FPU Affinity set after 11720 emulations
[ 0.577627] pull PCIe RST: RALINK_RSTCTRL = 4000000
[ 0.887570] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.897633] ***** Xtal 40MHz *****
[ 0.904366] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.914570] Port 0 N_FTS = 1b102800
[ 0.921472] Port 1 N_FTS = 1b102800
[ 0.928396] Port 2 N_FTS = 1b102800
[ 2.086869] PCIE2 no card, disable it(RST&CLK)
[ 2.095556] -> 21007f2
[ 2.100377] PCIE0 enabled
[ 2.105578] PCIE1 enabled
[ 2.110756] PCI host bridge /pcie@1e140000 ranges:
[ 2.120281] MEM 0x0000000060000000..0x000000006fffffff
[ 2.130642] IO 0x000000001e160000..0x000000001e16ffff
[ 2.141009] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 2.167810] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 2.179054] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 2.190233] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 2.202446] PCI host bridge to bus 0000:00
[ 2.210462] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 2.224126] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 2.237768] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 2.251241] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 2.267008] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 2.267046] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 2.267058] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 2.267122] pci 0000:00:00.0: supports D1
[ 2.267131] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 2.267354] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 2.267382] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 2.267395] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 2.267446] pci 0000:00:01.0: supports D1
[ 2.267455] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 2.267680] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 2.283469] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 2.299533] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280
[ 2.299583] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 2.299737] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[ 2.327259] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 2.327452] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
[ 2.327498] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[ 2.327625] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 2.327814] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 2.327831] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 02
[ 2.327893] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 2.340915] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.354732] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 2.367867] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.381693] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 2.395166] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
[ 2.408650] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff]
[ 2.422132] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff]
[ 2.435610] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[ 2.450127] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.459956] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.473452] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff]
[ 2.486932] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.496756] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
[ 2.511540] clocksource: Switched to clocksource GIC
[ 2.523086] NET: Registered protocol family 2
[ 2.531911] IP idents hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.545407] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 2.559135] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 2.571754] TCP: Hash tables configured (established 1024 bind 1024)
[ 2.584478] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.595972] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.608618] NET: Registered protocol family 1
[ 2.617198] PCI: CLS 0 bytes, default 32
[ 2.851487] 4 CPUs re-calibrate udelay(lpj = 2924544)
[ 2.863138] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 2.884643] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.902272] io scheduler noop registered
[ 2.909918] io scheduler deadline registered (default)
[ 2.920141] io scheduler mq-deadline registered
[ 2.929114] io scheduler kyber registered
[ 2.986670] serial8250_init
[ 2.992132] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 3.006281] console [ttyS0] disabled
[ 3.013329] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 18, base_baud = 3125000) is a 16550A
[ 3.031291] console [ttyS0] enabled
[ 3.045060] bootconsole [early0] disabled
[ 3.061340] Ralink gpio driver initialized
[ 3.071248] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[ 3.085306] Enable NFI Clock
[ 3.091032] # MTK NAND # : Use HW ECC
[ 3.098348] Device not found, ID: c2f1
[ 3.105853] Not Support this Device!
[ 3.113333] chip_mode=00000001
[ 3.119398] Support this Device in MTK table! c2f1
[ 3.129290] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[ 3.142164] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
[ 3.154816] nand: Macronix NAND 128MiB 3,3V 8-bit
[ 3.164188] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 3.179279] Scanning device for bad blocks
[ 3.427109] MT7621-NAND: parsing partitions cmdlinepart
[ 3.437509] MT7621-NAND: got parser cmdlinepart
[ 3.446587] 8 fixed-partitions partitions found on MTD device MT7621-NAND
[ 3.460102] Creating 8 MTD partitions on "MT7621-NAND":
[ 3.470522] 0x000000000000-0x000000100000 : "u-boot"
[ 3.481397] 0x000000100000-0x000000200000 : "SC PART_MAP"
[ 3.493025] 0x000000200000-0x000002e00000 : "linux"
[ 3.503890] 0x000000600000-0x000002e00000 : "ubi"
[ 3.514377] 0x000002e00000-0x000004600000 : "ddwrt"
[ 3.525097] 0x000004600000-0x000004800000 : "factory"
[ 3.536001] 0x000004800000-0x000004a00000 : "nvram"
[ 3.546569] 0x000004a00000-0x000008000000 : "reserved1"
[ 3.558263] [mtk_nand] probe successfully!
[ 3.567136] Signature matched and data read!
[ 3.575636] load_fact_bbt success 1023
[ 3.653366] mtk_soc_eth 1e100000.ethernet: generated random MAC address ea:2e:b8:4f:31:d6
[ 5.069441] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
[ 5.081962] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 20
[ 5.098745] PPP generic driver version 2.4.2
[ 5.107453] PPP BSD Compression module registered
[ 5.116836] PPP Deflate Compression module registered
[ 5.126906] PPP MPPE Compression module registered
[ 5.136461] NET: Registered protocol family 24
[ 5.145712] i2c /dev entries driver
[ 5.153794] GACT probability NOT on
[ 5.160754] Mirror/redirect action on
[ 5.168088] Simple TC action Loaded
[ 5.175794] netem: version 1.3
[ 5.181899] u32 classifier
[ 5.187267] Performance counters on
[ 5.194898] input device check on
[ 5.202181] Actions configured
[ 5.208948] Netfilter messages via NETLINK v0.30.
[ 5.218588] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 5.230818] nf_conntrack_rtsp v0.7 loading
[ 5.239421] xt_time: kernel timezone is -0000
[ 5.248128] ip_set: protocol 6
[ 5.254477] gre: GRE over IPv4 demultiplexor driver
[ 5.264293] nf_nat_rtsp v0.7 loading
[ 5.271417] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 5.282450] NET: Registered protocol family 17
[ 5.291429] Bridge firewalling registered
[ 5.299422] 8021q: 802.1Q VLAN Support v1.8
[ 5.308523] registered taskstats version 1
[ 5.318214] searching for nvram
[ 5.324535] nvram size = 2097152
[ 5.905516] found nvram at 1E0000
[ 5.933233] auto-attach mtd3
[ 5.933269] ubi0: attaching mtd3
[ 6.313244] ubi0: scanning is finished
[ 6.335540] ubi0: attached mtd3 (name "ubi", size 40 MiB)
[ 6.346308] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 6.359988] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 6.373503] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 6.387356] ubi0: good PEBs: 320, bad PEBs: 0, corrupted PEBs: 0
[ 6.399307] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 6.413695] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1045983397
[ 6.431873] ubi0: available PEBs: 0, total reserved PEBs: 320, PEBs reserved for bad PEB handling: 20
[ 6.450242] ubi0: background thread "ubi_bgt0d" started, PID 932
[ 6.452864] block ubiblock0_0: created from ubi0:0(rootfs)
[ 6.473132] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 6.486995] hctosys: unable to open rtc device (rtc0)
[ 6.504629] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 6.519302] Freeing unused kernel memory: 216K
[ 6.528181] This architecture does not have kernel memory protection.
[ 9.969437] Loading modules backported from Linux version v5.15.33-0-g06f50ca83ace
[ 9.984540] Backport generated by backports.git v5.15.33-1-0-g183c4ab2
[ 10.600487] bus=0x1, slot = 0x0, irq=0x0
[ 10.608380] PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
[ 10.620010] disable 2 ghz range
[ 10.626317] mt7615e 0000:01:00.0: Read calibration data from part factory, offset 0x00008000, len 0x00004DA8
[ 10.655676] initialize fq_codel with 262144 bytes memory limit
[ 10.667901] ieee80211_txq_setup_flows: set limit to 16777216 bytes
[ 10.680717] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 10.795022] bus=0x2, slot = 0x1, irq=0xff
[ 10.803109] PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
[ 10.814508] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
[ 10.814508]
[ 10.833773] mt7603e 0000:02:00.0: ASIC revision: 76030010
[ 10.844630] disable 5 ghz range
[ 10.850925] mt7603e 0000:02:00.0: Read calibration data from part factory, offset 0x00000000, len 0x00000400
[ 10.872309] no 5ghz
[ 11.056264] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649
[ 11.080692] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190415154149
[ 11.978592] mt7603e 0000:02:00.0: Firmware Version: ap_pcie
[ 11.989721] mt7603e 0000:02:00.0: Build Time: 20160107100755
[ 12.041533] mt7603e 0000:02:00.0: firmware init done
[ 12.219235] initialize fq_codel with 262144 bytes memory limit
[ 12.231314] ieee80211_txq_setup_flows: set limit to 16777216 bytes
[ 12.244079] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 13.849481] mtk_soc_eth 1e100000.ethernet: PPE started
[ 16.078533] device br0 entered promiscuous mode
[ 16.156141] br0: port 1(vlan1) entered blocking state
[ 16.167426] br0: port 1(vlan1) entered disabled state
[ 16.180574] device vlan1 entered promiscuous mode
[ 16.192290] device eth0 entered promiscuous mode
[ 16.209349] br0: port 1(vlan1) entered blocking state
[ 16.220484] br0: port 1(vlan1) entered forwarding state
[ 16.231053] device br0 left promiscuous mode
[ 16.244805] device br0 entered promiscuous mode
[ 16.266757] device br0 left promiscuous mode
[ 20.242265] br0: port 2(wlan1) entered blocking state
[ 20.254386] br0: port 2(wlan1) entered disabled state
[ 20.267516] device wlan1 entered promiscuous mode
[ 20.279382] br0: port 2(wlan1) entered blocking state
[ 20.292093] br0: port 2(wlan1) entered forwarding state
[ 29.079433] br0: port 3(wlan0) entered blocking state
[ 29.091672] br0: port 3(wlan0) entered disabled state
[ 29.105045] device wlan0 entered promiscuous mode
[ 29.116661] br0: port 3(wlan0) entered blocking state
[ 29.129351] br0: port 3(wlan0) entered forwarding state
[ 29.200931] mtk_soc_eth 1e100000.ethernet eth0: port 4 link up
[ 29.479388] device vlan2 entered promiscuous mode
[ 31.091619] random: crng init done
[ 31.376426] fast-classifier (PBR safe v2.1.6b): starting up
[ 31.387837] fast-classifier: registered
[ 31.484076] Linux kernel CIFS/SMB SERVER 3.4.6 by Namjae Jeon <linkinjeon@kernel.org>
[ 31.728616] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 32.384068] device vlan2 left promiscuous mode
[ 32.953082] usbcore: registered new interface driver usbfs
[ 32.964252] usbcore: registered new interface driver hub
[ 32.975023] usbcore: registered new device driver usb
[ 33.302374] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 33.313113] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[ 33.331696] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010
[ 33.349977] xhci-mtk 1e1c0000.xhci: irq 19, io mem 0x1e1c0000
[ 33.362519] hub 1-0:1.0: USB hub found
[ 33.370138] hub 1-0:1.0: 2 ports detected
[ 33.379326] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 33.390169] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[ 33.405179] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 33.418496] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 33.435628] hub 2-0:1.0: USB hub found
[ 33.443257] hub 2-0:1.0: 1 port detected
[ 33.893749] SCSI subsystem initialized
[ 34.118326] usbcore: registered new interface driver usb-storage
[ 35.203641] fast-classifier: shutting down
[ 35.518758] fast-classifier (PBR safe v2.1.6b): starting up
[ 35.530098] fast-classifier: registered
[ 36.398602] fast-classifier: shutting down
[ 37.986474] fast-classifier (PBR safe v2.1.6b): starting up
[ 37.997860] fast-classifier: registered
[ 81.564641] fast-classifier: shutting down
[ 81.877970] fast-classifier (PBR safe v2.1.6b): starting up
[ 81.889542] fast-classifier: registered
[ 82.555034] fast-classifier: shutting down
[ 84.640690] fast-classifier (PBR safe v2.1.6b): starting up
[ 84.652025] fast-classifier: registered
[ 3912.289981] mtk_soc_eth 1e100000.ethernet eth0: port 4 link down
[ 3915.481386] mtk_soc_eth 1e100000.ethernet eth0: port 4 link up
[ 7123.785837] mtk_soc_eth 1e100000.ethernet eth0: port 3 link up
[ 7616.723442] mtk_soc_eth 1e100000.ethernet eth0: port 3 link down
[ 7622.333091] mtk_soc_eth 1e100000.ethernet eth0: port 3 link up
[ 7623.823132] mtk_soc_eth 1e100000.ethernet eth0: port 3 link down
[ 7626.760938] mtk_soc_eth 1e100000.ethernet eth0: port 3 link up
[ 7693.753549] mtk_soc_eth 1e100000.ethernet eth0: port 3 link down
[ 7696.605585] mtk_soc_eth 1e100000.ethernet eth0: port 3 link up
[ 7704.242263] mtk_soc_eth 1e100000.ethernet eth0: port 3 link down
[ 7707.165844] mtk_soc_eth 1e100000.ethernet eth0: port 3 link up
|
|
|